WhatsApp Get Quote Send Email
When you operate fiber laser cutting machine, you should do regular maintenance works for long lifespan, thus, how to maintain it daily? You will get in this guide.

 Jan 24, 2016    2189 (3 Min Read)

Fiber Laser Cutter Daily Maintenance Criterion

1. Before starting up the fiber laser cutting machine, first check the 2nd and 3rd reflecting mirror, as well as check whether there is any dust on the mirror or any broken in the mirror.

2. Before cutting, please make sure the belows:

A. Check the pressure of air compressor to make sure its no less than 0.8Mpa, and try to open the protection air and up-down gun to check whether is smooth.

B. First up the cutting head, then run aside the edge frame, make sure the cutting pieces within the range of the setting area.

C. Simulate the processing output, make sure the cutting order whether is reasonable.

D. Adjust the height of cutting head to the suitable drilling place.

3. When cutting, observe whether is cutting out at any moment, if not, first up the cutting head by hand then stop cutting, and check the cutting parameter whether is right, and the spray nozzle and protecting mirror whether is damage, adjust well, then return back to un-cutting, then continue to cut.

4. When cutting, observe the cutting piece whether is turning over or up. If so, take over it in case of the collision between cutting head and piece, if the sheets is not plain, adjust its to the suitable drilling height (3-5mm) at any moment.

5. When cutting, observe the cutting head whether is fire up, if so, stop cutting, and check the spray nozzle about the abrasion, judge the focus whether is changing, if so, increase or reduce the pad depended the situation.

6. Every month clean the water-cooling machine one or two times, change the cycled water inside its, and use the distilled water without any impurity, can not use the tap water. purified water or mineral water.

7. Must make sure the close down of light out signal and protecting gas so that it can change the spray nozzle. protecting mirror and focus mirror and so on.

8. Clean off the metal dregs in the suctiondraft slagcatcher.

9. After the laser power supply electrified, at any time can not have a direct eye to the light out hole and any place the laser may be reflecting.

Fiber laser cutting machine

Maintenance Schedule for Fiber Laser Cutting Machine

No.Check CycleCheck PlaceCheck Requirement
1EverydayWorking tableClean it
2EverydayX axis leather tigerKeep its move smoothly
3EverydayConnect wireCheck each wire whether is tense and broken
4EverydayControl boxCheck the fan of control box whether is normal
5Every weekX axis screwOpen the leather tiger and clean screw, then add oil
6Every weekY axis screwClean screw, then add oil
7OccasionallyCheck computerAntiVirus. Disk tidy
8OccasionallyScrew nutCheck the fixing screw of screw nut whether is damaging
9Every day & weekProtecting mirror.Check mirror and clean it
10OccasionallyWater path. wind pathCheck the joint of water pipe and wind pipe whethe is damaging and blocking

In order to enhance the using life and cutting precision of the fiber laser cutting machine, please operate as above. Use the original qualified Consumable, if not, it will cause the serious fault.

What Are You Waiting For?

Once You MakeYour Choice, Don't Agonize Over It.

Get Your Free Quote

Further Reading

May 19, 2022 | 6 Min Read

A Guide to Buy an Affordable Laser Engraver or Laser Cutter

When you have an idea to buy an affordable laser engraver cutting machine to start your business, you should know what is a laser cutter engraving machine? what is it used for? how does it work? how much does it cost? how to buy it within your budget?

May 30, 2022 | 7 Min Read

A Guide to Buy Your First CO2 Laser Machine

Before you buy CO2 laser machine for engraving & cutting, you should know what is it? how does it work? how much does it cost? how to buy it within your budget.

May 27, 2022 | 6 Min Read

A Guide To Laser Cutting Basics

In this article, you will get the laser cutting basics, including definition, working principle, types, features, applications, and trends in future.

Jul 28, 2022 | 3 Min Read

How To Assemble & Setup CO2 Laser Engraving Cutting Machine?

Are you troubled by how to set up a CO2 laser engraving cutting machine? We have summed up 12 easy-to-follow steps on how to assemble a CO2 laser machine with pictures & videos.

Feb 25, 2022 | 4 Min Read

Digital Cutting Machine VS Laser Cutting Machine

Digital cutting machine and laser cutting machine are both flexible material cutting CNC machine tool with different features and advantages, so what are the differences between digital cutter and laser cutter?

Nov 12, 2022 | 4 Min Read

How to Laser Engrave & Cut Wood Projects at Home?

Are you planning to engrave & cut wood at home? A CO2 laser cutter & engraving machine can help you to easily make custom woodworking projects for hobby and commercial use to start or grow and expand your business.